HTM-30D251 HTM-30D351 HTM-40D251 HTM-40D351 HTM-55D251 HTM-55D351 HTM-60D251 HTM-60D351 HTM-65D251 HTM-65D351 HTM-80D251 HTM-80D351 HTM-85D251 HTM-85D351 Mechanical Seals

Structural features:

Double-end face modular mechanical seal. Easy to install and simple to use. Balanced design, with optional rotation direction.

Internal working length is short. The stationary ring features multi-spring external compensation that does not come into contact with the medium.

Applicable medium:

A medium with a high content of impurities such as gypsum and lime slurry.

Work parameters:

Fixed substance content: ≤30%

Warm Temperature: ≤280°C

Press Force: ≤2.5 MPa

Axis Diameter: ≤200mm

Material parameters:
Main material: 316L or 2205, 2507, 1.4529
Sealing ring material: SSiC or SiC
Rubber materials: Fluororubber or perfluoroether rubber

Main applications:

This type of mechanical seal is primarily used in flue gas desulfurization systems for coal-fired power plants, and is suitable for absorption tower slurry circulation pumps, gypsum slurry pumps, limestone slurry pumps, and gypsum discharge pumps.

Common pump numbers are as follows:

LCF40/250I LCF40/350I LCF40/400I LCF40/450I LCF50/350N2 LCF50/400I

LCF50/460I LCF65/310I LCF65/315I LCF65/350I LCF65/400I LCF80/400I

LCF80/450I LCF100/300 LCF100/320I LCF100/350I LCF100/420I LCF125/405I

LCF150/300I, LCF150/350I, LCF200/300I, LCF100/500T, LCF150/400I, LCF200/410I

LCF250/430I LCF250/430I LC300/500I LC300/530I LC300/400I LC300/635I

LC300/630I LC350/500I LC350/560I LC400/500I LC400/540I LC450/635I

LC500/630I LC550/700I LC550/710I LC550/750I LC600/825I LC700/900I

LC700/898I LC800/1000I LC900/1150I LC500/630II LC550/700II LC550/710II

LC550/750II, LC600/825II, LC700/900II, LC700/898II, LC800/1000II, LC900/1150II

Sealed model:

HTM-30S251Z HTM-30S351X HTM-30S330Z HTM-30S330Q

HTM-30D251ZZ HTM-30D351X

HTM-40S251Z HTM-40S351X HTM-40S330Z HTM-40S330Q

HTM-40D251ZZ HTM-40D351XX

HTM-55S251Z HTM-55S351X HTM-55S330Z HTM-55S330Q

HTM-55D251ZZ HTM-55D351XX

HTM-60S251Z HTM-60S351X HTM-60S330Z HTM-60S330Q

HTM-60D251ZZ HTM-60D351XX

HTM-80S251Z HTM-80S351X HTM-80S330Z HTM-80S330Q

HTM-80D251ZZ HTM-80D351XX

HTM-85S251Z HTM-85S351X HTM-85S330Z HTM-85S330Q

HTM-85D251ZZ HTM-85D351XX

LB-LK7-120S LB-LK7-120D LB-LK6-115S LB-LK6-115D

HTM-30S HTM-40S HTM-55S HTM-60S HTM-80S

HTM-30D HTM-40D HTM-55D HTM-60D HTM-80D

HR3-125 HR3-142 HR3-158 HR3-175 HR3-198

HR325/230 HR325/210 HR325/190 HR325/170

HRM-125D3 HRM-142D3 HRM-158D3 HRM-175D3 HRM-198D3

HRM-125S3 HRM-142S3 HRM-158S3 HRM-175S3 HRM-198S3

HMR3C-125 HMR3C-142 HMR3C-158 HMR3C-175 HMR3C-198

Installation Use Requirements :

1. The radial runout of the equipment shaft should not exceed 0.04 mm, with axial runout not exceeding 0.1 mm;
2. The sealing cavity areas of the equipment should be kept clean during installation, and sealing components must be thoroughly cleaned. Ensure that the sealing end faces remain intact to prevent contaminants and dust from entering the sealing area.
3. During installation, avoid any contact or tapping to prevent damaging the mechanical seal through friction, which could lead to sealing failure.
4. During installation, apply a layer of clean machine oil to the surfaces that will come into contact with the seal, ensuring smooth installation.
5. When installing the stationary ring gland, tighten the screws evenly to ensure the stationary ring face is perpendicular to the shaft centerline.
6. After installation, gently push the moving ring by hand to ensure it moves freely along the shaft while maintaining some elasticity.
7. After installation, manually rotate the shaft—there should be no sensation of unevenness or heaviness.
8. Before operating, the equipment must be fully charged with the medium to prevent dry friction, which could lead to seal failure.