ZU13N, ZU14N, ZB13N, ZB14N Mechanical Seals

ZU13N, ZU14N, ZB13N, ZB14N Mechanical Seals

Structural features:

1. Single-face, sleeve-driven design with a single spring—highly resistant to clogging. Operation is independent of rotation direction.

2. Depending on the specific application, auxiliary sealing rings can include rubber O-rings, PTFE V-rings, or PTFE wedge-shaped rings.

3. Complies with ISO 3069, DIN 24960, and GB 6556 standards, offering excellent versatility.

4. The ZB type features a balanced design similar to the ZU type, making it suitable for higher-pressure operating conditions.

Applicable medium:

Oil, water, acids, bases, salts, and more

Note: Since this type of pump has a wide range of applications, the sealing material (friction pair) also varies. To ensure reliable sealing performance,
The manufacturer recommends the following:
1. Clear water (without particulate matter)—Use an alloy for the dynamic sealing pair and graphite for the static sealing pair.
2. Highly corrosive environments (conditions involving particulate matter) – The dynamic seal friction pair is made of silicon carbide, while the stationary seal friction pair also uses silicon carbide.
3. Conditions involving particles and significant vibration—select (alloy) for the dynamic ring friction pair, and (alloy) for the stationary ring friction pair.
4. Customization is also available upon customer request. If no specific request is made, the default option will be (clear water).

Work parameters:

Fixed substance content: ≤20%

Warm Temperature: ≤280°C

Press Force: ≤4.0 MPa (ZU) ≤1.0 MPa/ZB ≤4.0 MPa )

Axis Diameter: ≤200mm

Material parameters:
Main material: 304, 316L or 2205, 2507, 1.4529
Sealing ring materials: M106D, YWN8, SSiC or SiC
Rubber materials: Fluororubber or perfluoroether rubber

Main applications:

This seal can be used in various types of water pumps and chemical pumps.

The models are as follows:

ZU14N-25  ZU14N-30  ZU14N-35  ZU14N-40  ZU14N-45

ZU14N-50  ZU14N-55  ZU14N-60  ZU14N-65  ZU14N-70

ZU14N-75  ZU14N-80  ZU14N-85  ZU14N-90  ZU14N-95

ZU14N-100  ZU14N-105 ZU14N-110  ZU14N-115  ZU14N-120

ZU13N-25  ZU13N-30  ZU13N-35  ZU13N-40  ZU13N-45

ZU13N-50  ZU13N-55  ZU13N-60  ZU13N-65  ZU13N-70

ZU13N-75  ZU13N-80  ZU13N-85  ZU13N-90  ZU13N-95

ZU13N-100  ZU13N-105 ZU13N-110  ZU13N-115 ZU13N-120

Z B 14N-25   Z B 14N-30   Z B 14N-35   Z B 14N-40   Z B 14N-45

Z B 14N-50   Z B 14N-55   Z B 14N-60   Z B 14N-65   Z B14N-70

Z B 14N-75   Z B 14N-80   Z B 14N-85   Z B 14N-90   Z B 14N-95

Z B 14N-100   Z B14N-105  Z B 14N-110  Z B 14N-115   Z B 14N-120

Z B 13N-25   Z B 13 N-30   Z B 13N-35   Z B 13N-40   Z B 13N-45

Z B 13N-50   Z B 13N-55   Z B 13N-60   Z B 13N-65   Z B 13N-70

Z B 13N-75   Z B 13N-80   Z B 13N-85   Z B 13N-90   Z B 13N-95

Z B 13N-100   Z B 13N-105  Z B13 N-110 Z B 13 N-115 Z B 13N-120

Installation Use Requirements :

1. The radial runout of the equipment shaft should not exceed 0.04 mm, with axial runout not exceeding 0.1 mm;
2. The sealing cavity areas of the equipment should be kept clean during installation, and sealing components must be thoroughly cleaned. Ensure that the sealing end faces remain intact to prevent contaminants and dust from entering the sealing area.
3. During installation, avoid any impact or hammering to prevent damaging the mechanical seal through friction and compromising its sealing performance.
4. During installation, apply a layer of clean machine oil to the surfaces that will come into contact with the seal, ensuring smooth installation.
5. When installing the stationary ring gland, tighten the screws evenly to ensure the stationary ring face is perpendicular to the shaft centerline.
6. After installation, gently push the moving ring by hand to ensure it moves freely along the shaft while maintaining some elasticity.
7. After installation, manually turn the shaft—there should be no sensation of unevenness or heaviness.
8. Before starting operation, the equipment must be fully charged with the medium to prevent dry friction, which could lead to seal failure.