HM74D-45SGA, HM74D-60SGA, HM74D-85SG, HM74D-100SGA, HM74D-125SGA, HM74D-140SGA Mechanical Seals

Structural features:

Double-end face non-container mechanical seal. Offers excellent sealing performance and easy maintenance. Non-balanced design, with optional rotation direction.

Internal working length is short. Multiple spring compensation ensures even pressure distribution on the sealing surfaces.

Applicable medium:

A medium with a high content of impurities such as gypsum and lime slurry.

Work parameters:

Fixed substance content: ≤30%

Warm Temperature: ≤280°C

Press Force: ≤2.5 MPa

Axis Diameter: ≤200mm

Material parameters:
Main material: 316L or 2205, 2507, 1.4529
Sealing ring material: SSiC or SiC
Rubber materials: Fluororubber or perfluoroether rubber

Main applications:

This type of mechanical seal is primarily used in flue gas desulfurization systems for coal-fired power plants, and is suitable for absorption tower slurry circulation pumps, gypsum slurry pumps, limestone slurry pumps, and gypsum discharge pumps.

Common pump numbers are as follows:

25DT-A15 25DT-A25 40DT-A17 40DT-A19 40DT-B20 40DT-A25

40DT-A30 40DT-B35 40DT-A40 50DT-A30 50DT-B40 50DT-D40

50DT-A45 50DT-A50 65DT-A30 65DT-A40 80DT-A30 80DT-A36

100DT-A35 100DT-B40 100DT-A45 100DT-A50 100DT-A60 100DT-A65

150DT-A40 150DT-A45 150DT-A50 150DT-B50 150DT-B55 150DT-A60

200DT-B45 200DT-A60 250DT-A45 250DT-A48 250DT-A52 250DT-A75

300DT-A50 300DT-A52 300DT-A60 300DT-A75 350DT-A48 350DT-A52

350DT-A58 350DT-A65 350DT-A68 350DT-A78 400DT-A65 450DT-A70

500DT-A70 500DT-A71 500DT-A73 500DT-A75

500DT-A76 500DT-A80 550DT-A70 550DT-A75 600DT-A80 600DT-A82

600DT-A83 700DT-A75 700DT-A80 700DT-A83 700DT-A85 700DT-A90

800DT-A90 800DT-F96 800DT-A100 900DT-F110

Sealed model:

HM74D-45SGA HM74D-45SGB HM74D-45SGC HM74D-45SGD

HM74D-60SGA HM74D-60SGB HM74D-60SGC HM74D-60SGD

HM74D-85SGA HM74D-85SGB HM74D-85SGC HM74D-85SGD

HM74D-100SGA HM74D-100SGB HM74D-100SGC HM74D-100SGD

HM74D-125SGA HM74D-125SGB HM74D-125SGC HM74D-125SGD

HM74D-140SGA HM74D-140SGB HM74D-140SGC HM74D-140SGD

HM74D-170SGA -188 HM74D-180SGA -188 HM74D-190SGA -188

Installation Use Requirements :

1. The radial runout of the equipment shaft should not exceed 0.04 mm, with axial runout not exceeding 0.1 mm;
2. The sealing cavity of the equipment should be kept clean during installation, and sealing components must be thoroughly cleaned. Ensure that the sealing faces remain intact to prevent contaminants and dust from entering the sealing area.
3. During installation, avoid any impact or hammering to prevent damaging the mechanical seal through friction, which could lead to sealing failure.
4. During installation, apply a layer of clean machine oil to the surfaces that will come into contact with the seal, ensuring smooth installation.
5. When installing the stationary ring gland, tighten the screws evenly to ensure the stationary ring face is perpendicular to the shaft centerline.
6. After installation, gently push the moving ring by hand to ensure it moves freely along the shaft while maintaining a certain degree of flexibility.
7. After installation, manually turn the shaft—there should be no sensation of unevenness or heaviness.
8. Before starting operation, the equipment must be fully charged with the medium to prevent dry friction, which could lead to seal failure.